A deck's condition usually points to one of three approaches: a clean and recoat, removing the failing finish and refinishing, or board repairs first. Some decks have worn down enough that they need structural replacement instead. Which approach fits depends on how far the wood and the existing finish have worn down.
A deck that has turned gray, lost its shine, or started peeling leaves an unclear next step before anyone asks for a price.
Photos of the deck's surface and finish, along with a few details, are usually enough to get a quote without an in-person visit first. The sections below walk through the signs that point to each path.
Clean and Recoat: When Your Deck Just Needs a Fresh Finish
Has your deck faded to gray while the old finish stays mostly intact? The wood needs to be solid, and the new coat needs to be compatible with what's already there. If both check out, a wash and a fresh coat may be enough. This is the simplest of the three paths.

The USDA Forest Service's research on wood deck finishes found that wood decks face constant stress from weather, which shrinks and swells the boards. Without proper upkeep, a deck can develop checks and cracks, raised grain and mildew, which increases the risk of decay and insect damage. Adding a fresh finish helps minimize cracking, raised grain and mildew growth on the wood.
GSA's wood-stain guidance recommends brushing off dust and loose wood fibers with a stiff brush when staining over a weathered penetrating natural finish. Follow the specific coating system's own preparation instructions to confirm it's compatible with what's already on the deck. Not every faded deck can skip a full strip.
Remove the Failing Finish: When the Old Coating Has to Come Off First
Peeling, flaking or cracked coating is a different problem than simple fading. Peeling and flaking mean the old finish has stopped sticking to the wood. Cracking alone doesn't always mean the same thing, but it's still worth a closer look. A deck with peeling or flaking coating needs the failing finish removed before any new stain or sealer goes on.

Removing a failing finish means taking off the coating that has stopped sticking. How much has to come off, sometimes down to bare wood, depends on the preparation steps of the new stain or sealer.
A manufacturer's prep guidance for recoating notes that any existing stain coating on a wood surface can prevent a new finish from fully penetrating. That guidance applies to the coating system it describes, so it does not mean every deck due for a maintenance recoat needs a full strip.
Repair Boards and Structural Issues Before Any Finish Goes On
A county deck safety checklist checks for wood rot, splitting and insect damage, including at the posts where they meet the ground. It also flags loose connections, corroded fasteners and unstable rails or stairs as safety concerns that call for a professional look before cosmetic work starts.

This checklist offers general structural safety guidance, not a Davenport building rule, though the same checks apply before any deck gets a new finish. The City of Davenport lists decks among the building work that needs a permit, grouped with additions, garages, remodels and new construction.
That listing groups decks with other construction and structural work needing a permit. It doesn't spell out whether a routine board swap needs one, so anyone planning repairs beyond a simple fix should check with the city directly.
Board repair means fixing or replacing damaged wood, such as a split plank, a soft board or a loose connection. This has to happen before any new stain or sealer goes on, so the finish has solid wood to hold onto.
Older and Pressure-Treated Decks: What to Check Before Restoring
Many decks built before 2004 use CCA-treated wood, an older type of pressure-treated wood. This wood needs special care when it is cleaned, sanded or thrown away, so follow EPA guidance for it. Its presence alone does not mean the deck has to be replaced.
According to the EPA's guidance on CCA-treated wood, removing an existing CCA-treated deck is not required just because of the treatment. An older pressure-treated deck is not automatically a replace-it situation. Structural condition, how the wood will be exposed, and what cleaning or refinishing methods are practical all factor into the decision.
If the home was built before 1978 and the deck has ever been painted, check for lead-based paint before sanding, scraping or stripping it, and follow the EPA's lead-safe guidance for do-it-yourself work.
Deck Condition at a Glance
The table below matches what you can see on your deck to the likely next step. Use it as a starting point before you request a quote.
| Visible condition | Likely next step | What photos alone can't confirm | When an on-site visit helps |
|---|---|---|---|
| Color has faded or grayed, and the existing finish is mostly intact | Clean and recoat, if the wood is sound and the new coat is compatible | Whether the wood underneath is fully sound | If any board feels soft or spongy when you walk the deck |
| Finish is peeling, flaking or cracked rather than simply faded | Remove the failing finish, following the new coating's prep steps | How much of the old coating has to come off | If stripped areas reveal splits or damage once uncovered |
| Boards feel soft or spongy, are split, show insect damage, or rails and posts feel loose | Repair boards first | How deep the damage goes beneath the surface | A hands-on check helps confirm any structural issue before refinishing |
This table is a starting point, not a diagnosis. Photos can narrow down which path your deck is likely on, but they cannot always show everything happening underneath the surface. The next section covers exactly what to photograph so your quote starts from the clearest picture possible.
Deck Staining vs. Deck Sealing (and Why Painting Isn't on the List)
Deck stain adds color to the wood. Transparent and semi-transparent stains still let the wood grain show through; solid-color stains cover more of it. Homeowners choose stain to refresh a faded deck or change its tone while keeping some look of real wood.
Deck sealer and stain overlap: many products combine color with waterproofing. A clear sealer protects the wood with little to no color change, keeping its current tone, but sealers also come in tinted or solid-color versions. A reader who likes the wood's current color and just wants to protect it can ask about a clear option.
Paint forms a solid film that fully covers the wood grain. Some solid-color stains and stain-and-sealer products form a similar film, so the line between paint and the darkest stains can blur. Once a painted or film-forming finish starts to fail, it needs the failing area removed and prepped before any recoat, not just a quick touch-up.
Always Clean's Restoration Process: Wash, Repair, Recondition, Stain and Seal
The approach above draws on the real steps Always Clean uses to restore a deck. Its Deck & Wood Restoration service covers washing, repairing, reconditioning, staining and sealing, mainly for homes. Jobs like this are quoted from photos.
The company is family-owned by Chad and Angela Ingwersen, based in Eldridge, Iowa, and it is not a franchise. Read more about the owners on the company's about page. It carries insurance on every job, is bonded, and background-checks its staff.
The company serves Davenport and Bettendorf first, along with Eldridge and the wider Quad Cities. Check the service area list to confirm coverage for your address.
What to Photograph for an Accurate Quote
A few clear photos can help Always Clean quote your deck without an in-person visit first. This is advice to help you prepare, not an official requirement.
- Overall views of the deck from a few steps back on each side, showing the full surface and railings.
- Close-up shots of any spot where the finish is peeling, flaking or cracked.
- Close-up shots of any board that looks damaged, soft or discolored.
- Rough dimensions, such as the deck's length and width or the number of steps.
Jobs like this can usually be quoted from these details and photos. Send your photos when you request a quote below.
Deck Restoration FAQ
Is it better to sand or pressure wash a deck?
There's no direct evidence comparing sanding to pressure washing. If your deck is older, it may be CCA-treated wood that needs special care, so ask Always Clean which method fits it.
Ready to Restore Your Deck? Here's Your Next Step
Always Clean's Deck & Wood Restoration service washes, repairs, reconditions, stains and seals residential decks, once you know which path yours needs. Gather your photos and dimensions, then Get a Free Quote to get an estimate for the work it needs.